Nano Lok Twin Leg SRL - For Hot Work Use

Nano-Lok™ Twin-Leg Quick Connect Self Retracting Lifeline - Web - For Hot Work Use

Model: 3101503

6 ft. (1.8m) twin-leg lifelines with 3/4" (19mm) Kevlar® web and aluminum carabiner, swiveling anchor loop.

• For hot work use
• Twin-leg 100% tie-off design
• Built-in connector for twin-leg SRL direct attachment to harness
• 6 ft. (1.8m) twin-leg lifelines with 3/4" (19mm) Kevlar® fiber webbing
• Aluminum self-locking carabiner on each lifeline
• Tough and impact resistant thermoplastic housing
• Swiveling anchorage loops
• Quick activating speed sensing brake systems
• High capacity energy absorber and impact indicator protected by Kevlar® fiber cover
• i-Safe™ equipped
• Wide variety of configurations available

• Capacity 420 lbs. (190 kg)
• Brand DBI-SALA®
• Sub Brand Nano-Lok™
• Size 6 ft. (1.8m)
• iSafe Equipped Yes
• Lifeline Length 6 ft. (1.8m)
• Housing Nylon Thermoplastic
• Lifeline Hook Aluminum
• Lifeline 3/4" (19mm) wide Kevlar®
• Model 3101503
• Physical Dimensions 20.45x3.05x2.03 (in)
• Physical Weight 5.40 lbs (2.4kg)
• Product Styles Twin Lifelines (100% tie-off)
• Product Types Harness Mounted Arc Flash Welding
• Housing Type Thermoplastic
• Lifeline Type Fire Resistant Web
• Mounting Type Direct to Harness Back
• Weight Group 5 to 10 lbs. (2.3 to 4.5 kg)
• Standards ANSI Z359.14, OSHA 1910.66, OSHA 1926.502, ANSI A10.32, Capital Safety Gen. Mfg. Req.

Instructions are provided for informational purposes, customers need not to worry about a complicated attachment procedure. The Nano-Lok SRL's are designed with ease of use for the customer to install correctly. So, don't get caught up, thinking this is a really daunting task, it is a so easy to install an Iron Worker could do it.

Twin SRL Harness Interface: In climbing applications where 100% tie-off is required, the Twin SRL Harness Interface can be used to mount two Nano-Lok SRLs side-by-side on the back of a Full Body Harness just below the Dorsal D-Ring (see Figure 9). To mount two Nano-Lok SRLs on a Full Body Harness with the Twin SRL Harness Interface:

1. Loosen the Harness Webbing: Pull out on the Web Straps (A) where they pass through the bottom of the Dorsal D-Ring (B) until there is sufficient space to slide the Twin Leg Interface between the Web Straps and D-Ring Pad.

2. Open the Harness Interface: Push up on the Connector Insert (C) to unsnap the Clamps (D) from the Connector and then swing the Connector Insert up to unlock the Gate. Push the Gate (E) inward to open the Connector.

3. Thread the first Nano-Lok SRL onto the Harness Interface: Insert the Nose of the Connector (F) through the Swivel Eye (G) on the SRL and then rotate the SRL around to the Gate End of the Connector (H). The Gate can be rotated toward the Nose to allow clearance for the Swivel Eye between the Gate and Spine of the Connector.

4. Position the Harness Interface around the Web Straps: With the Gate facing up, insert the Nose of the Connector (F) behind the Web Straps (A). Rotate the Connector behind the Web Straps until the Connector surrounds the the Web Straps.

5. Add the second Nano-Lok SRL on the Harness Interface: Slide the SRL’s Swivel Eye (G) over the Nose of the Connector (F) and position the SRL Swivel Eye in the Nose End of the Connector (I). Swing the Gate (E) closed.

6. Close the Harness Interface: Rotate the Connector Insert (C) forward so the Clamps (D) secure on the Connector. When properly closed, the Web Straps should pass through the Webbing Slot (J) at the top of the Connector Insert and the SRL Swivel Eyes should be secured in the Recesses (K) on either side of the Connector Insert. Once the Harness Interface is closed, pull the Web Straps (A) back through the Dorsal D-Ring and D-Ring Pad to eliminate slack in the webbing and secure the Connector between the Web Straps and D-Ring Pad.