DBI SALA Nano-Lok Self Retracting Lifeline - Quick Connect - 6' Single Leg

Our Price: $239.59

Availability: Usually Ships in 24 to 48 Hours
Product Code: 3101225--3100523

Qty:

Description

Technical Specs

6 ft. Nano-Lok Single Leg Self Retracting Lifeline with Quick Connector

3101225

Replace your lanyard to reduce fall distance and improve your safety program with the Nano-Lok™ Self Retracting Lifeline.

Nano-Lok™ is ergonomically designed for ease-of-use and is ideal for direct connection to most harnesses. The unique twin-leg SRL quick connector design leaves the dorsal D-ring available for other uses and provides a snug fit - it's virtually unnoticeable on your back!

Product Details:

Single Leg 6 ft. compact web self retracting lanyard
420 lb. Capacity
Only weighs 1.97 lbs. in this model
3101225: Nano-Lok™ Single Leg Self Retracting Lifeline with Quick Connector anchorage connection and aluminum carabiner (captive eye)

Instructions are provided for informational purposes, customers need not to worry about a complicated attachment procedure. This SRL's are designed with ease of use for the customer to install correctly. So, don't get caught up, thinking this is a really daunting task, it is a so easy to install an Iron Worker could do it.

HARNESS MOUNTING

• Single SRL Harness Interface: Where worker mobility is critical, a Single SRL Harness Interface can be used to mount the Nano-Lok SRL on the back of a Full Body Harness just below the Dorsal D-Ring (see Figure8). The worker can then connect to varied anchorage points located throughout the site with the Lanyard End of the SRL without repeatedly re-installing the SRL. To mount the Nano-Lok SRL on a Full Body Harness with the Single SRL Harness Interface:

1. Loosen the Harness Webbing: Pull out on the Web Straps (A) where they pass through the bottom of the Dorsal D-Ring (B) until there is sufficient space to slide the Single Leg Interface between the Web Straps and Back Pad.

2. Open the Harness Interface: Push down on the Locking Buttons (C) simultaneously and slide theLocking Pin (D) out.

3. Position the Harness Interface around the Web Straps: With the Locking Buttons (C) facing out and Gate facing up, insert the Nose End of the Harness Interface (E) behind the Web Straps (A). Rotate the Harness Interface behind the Web Straps until the Harness Interface surrounds the the Web Straps. Pull the Web Straps back through the Dorsal D-Ring and Back Pad to secure the Harness Interface.

4. Attach the Nano-Lok SRL to the Harness Interface: Slide the Swivel Eye on the SRL (F) over the Harness Interface’s Locking Pin (D) and then push in the Locking Pin until it locks into place in the opposite end of the Harness Interface.

WARNING: The Red Band on the knob end of the Harness Interface Locking Pin will be exposed if the Harness Interface is unlocked. To avoid accidental release of the connection, always make sure the Harness Interface is locked before using the Harness and attached Nano-Lok SRL. Failure to do so could result in injury or death.

NOTE: It is also acceptable to connect the Nano-Lok SRL to the Harness Dorsal D-Ring with a Carabiner or Snaphook.

dbi nano lok instructions single connector

dbi nano lok instructions single connector

Share your knowledge of this product. Be the first to write a review »

Browse for more products in the same category as this item:

Retractable Lifelines > Retractable Lanyards > Web
Retractable Lifelines
Manufacturers > DBI-SALA
Retractable Lifelines > Retractable Lanyards > Web > 6 ft. to 8 ft. Web SRL's